BF flotation cell has two types: type I and type II. Type I is improved as suction cell referring to model SF; type II is improved as direct flow cell referring to model JJF.
Each feeding inlet of Xinhai cyclone unit is installed knife gate valve independently developed by Xinhai. This valve with small dimension reduces the diameter of cyclone unit.
The supports at both ends of cone crusher main shaft, scientific design of crushing chamber, double insurance control of hydraulic and lubricating system.
Wet type overflow ball mill is lined with Xinhai wear-resistant rubber sheet with excellent wear resistance, long service life and convenient maintenance
Wet type grid ball mill is lined with Xinhai wear-resistant rubber sheet with excellent wear resistance design, long service life and convenient maintenance.
Ring groove rivets connection, plate type screen box, advanced structure, strong and durable Vibration exciter with eccentric shaft and eccentric block, high screening efficiency, large capacity
Xinhai improves the traditional specification of crushing chamber by adopting high speed swing jaw and cambered jaw plate.
High-speed hammer impacts materials to crush materials. There are two ways of crushing (Wet and dry)
The cone slide valve is adopted; the failure rate is reduced by 80%; low energy consumption;the separation of different material, improvement of the processing capacity by more than 35%.
Cylindrical energy saving grid ball mill is lined grooved ring plate which increases the contact surface of ball and ore and strengthens the grinding.
20-30%. Rolling bearings replace slipping bearings to reduce friction; easy to start; energy saving 20-30%
Both sides of the impeller with back rake blades ensures double circulating of slurry inside the flotation tank. Forward type tank, small dead end, fast foam movement
Copper Slag,Copper Cathode,Copper Reverts , Find Complete Details about Copper Slag,Copper Cathode,Copper Reverts,Copper Slag from Copper Scrap
Beneficiation by froth flotation of ore to give copper concentrate. Optional partial intermediate products e.g., cement copper or copperI oxide precipitates, reverts e.g., converter slag, refining slag, or flue dusts, and copper-alloy scrap.
tons of refined copper cathodes. Copper electrolytic refining with permanent cathode technology per-bearing reverts to produce molten slag and matte.
impurities as converter slag and to form blister copper. Blister copper is further refined as either fire- refined copper or anode copper 99.5% pure cop-.
800,000 to 900,000 tpa of copper cathode Mining. Journal, 2002. . molten pool containing both matte and slag phases. The . scrap, residues, and reverts.
S-furnace, feed materials of copper concentrate, flux and in-plant reverts, are charged launders that divert the flow of blister to any anode furnace at will.
slags: giving additional value to copper mining industry. VII International converter, Anode and fire refining furnaces, and reverberatory furnaces are described
In the slag-making stage, impure scrap with a lower copper content can be used, Copper alloy scrap is added to the TBRC and to the anode furnace www. . Most smelters melt scrap copper and solid reverts in the Peirce–Smith converter.
Further, copper can be recovered from tailing and slag using certain processes .. Electrolysis of leachate converts copper ion to a cathode copper, which is the
to gas and distribution coefficient wt% matte j wt% slag was analyzed In electrorefining, Pb was found to report predominantly to anode slimes while Ni Therefore, it is believed that the future of copper smelting and refining the copper concentrate, silica-based flux, air or oxygen-enrich air, recycled dust, reverts and.
Keywords: Sulphide smelting, Copper, Slag, Blister copper, Flash smelting .. dust and revert circulations of the smelter. .. applied, and the high-grade converter matte was further refined to nickel cathodes by leaching and electrowinning.
Kidd Process stainless steel cathode technology, poly- the recycle of a copper slag concentrate to the smelt- nace is also used to melt internal reverts.
Dec 1, 1990 proven pyro-metallurgical process to produce blister copper continuously from concentrates. 1 Anode. Anode copper. Anode furnace. C-furnace. C-slag recyled to. S-furnce . Materials, such as in-plant reverts and circuit
Copper extraction refers to the methods used to obtaining copper from its ores. The conversion .. Thus, the two factors that most affect the loss of copper to slag in the smelting stage are: . At the cathode, copper metal plates out, but less noble constituents such as arsenic and zinc remain in solution unless a higher voltage
Nov 12, 2013 Direct-to-blister smelting of copper concentrates: the slag fluxing chemistry . 3 has been simplified by omitting the internal flue dust and revert
Copper is extracted from various ores or recovered from waste and scrap. is SX-EW production that can be treated as refined cathode and sold as such. the copper sulphide from the gangue and other metals which form a slag that floats
Recycling copper converter slag back to the flash furnace has been practiced and leads to an . Note: This table shows primary metal in the form of blister and anode produced .. Another method is a reduction process that converts iron oxide.
streams: copper-iron-sulfide matte and slag in addition to sulfur dioxide gas. acid plant, which converts the sulfur dioxide-rich gases to sulfuric acid a useable redeposited on the cathode starting sheet, which is relatively pure copper with.
Typically, blister copper is then fire-refined in an anode furnace, cast into. "anodes", and The copper sulfide is removed and the remaining slag is discarded.
Achievements. 1. Achievement on physical performance 2017-18. i. Total Copper sales during the year 2017-18 was best in last seven years. ii. Copper cathode
Jul 8, 2015 Smelting history goes back at least 6000 years to the copper smelters of the the melt, making it easier to separate the metal from the slag. . The anticipated cathode production from Nkana was to be in the range 140 to 150.
2.2.4 Plants for copper production and further processing of copper cathodes. Table 3-38: Chemical composition of blast furnace slag from MKM . The heat generated during matte blowing is used for melting internal reverts like ladle
sold directly as cathode copper sheets, or cast into bars, ingots or slabs with a purity of up to or over . Copper from the flash furnace and the slag-cleaning furnace, that is referred to as blister copper . The MIC converts the matte into blister.
Copper Cathode Note: SEC Values are inclusive of all Units in Sterlite Copper Business . when the high volume of reverts treated . Copper Slag Road.
May 1, 2013 Copper, Copper Mining, and Copper Processing Copper anode slab after it is taken from a furnace to be molded. 38 where matte is a mixture of copper, sulfur and iron and slag is a dense, glassy material made of Pioneer operated it as a landscape rock mine up 2 years ago and it reverted back to.
Cathode copper has become the single most important commercial form converting and a liquid slag 0.3 to 0.8% Cu: 1200oC which is discarded as . converts to ferric sulphate which contributes to further leaching of copper minerals.
Search Indian Copper Slag Manufacturers and Suppliers Details - Contact to Copper Slag, Hindustan copper, Abrasive grit suppliers, Copper Cathodes, Slag copper, Copper Slag Powder, Copper slag suppliers, copper reverts, Copper slag
1993-2018 Xinhai Machine . All rights reserved | Design by Xinhai